Product Details:
Payment & Shipping Terms:
|
Application: | Indoor, Lab, Testing Center In LED Industry | High Temperature Chamber: | +60~200℃ |
---|---|---|---|
Conversion Time: | 3 Min | Internal Volume: | 1000L |
Test Chamber Temp. Range: | -40ºC~+150ºC | Cooling Method: | Water Cooled |
High Light: | thermal shock chamber,environmental testing chambers |
Cool And Heating Environmental Thermal Shock Test Chamber For Thermal Cycling Test
KOMEG specification for KTS-72A.pdf
1. Specifications
Model |
|
|||||||||||
70A | 130A | 226A | 360A | 500A | ||||||||
Test weight(KG) | 5 | 5 | 5 | 5 | 10 | |||||||
Interior size | W(mm) | 410 | 520 | 610 | 710 | 810 | ||||||
H(mm) | 560 | 670 | 770 | 830 | 710 | |||||||
D(mm) | 410 | 520 | 610 | 770 | 860 | |||||||
Basket size | W(mm) | 300 | 410 | 510 | 610 | 710 | ||||||
H(mm) | 300 | 410 | 510 | 730 | 610 | |||||||
D(mm) | 300 | 410 | 510 | 510 | 730 | |||||||
Low Temp. chamber | -55ºC~-10ºC | |||||||||||
Pre-cooling time | +20ºC~-55ºC, Within 60 min | |||||||||||
Test. chamber | -40ºC~+150ºC | |||||||||||
High Temp. chamber | +60ºC~+200ºC | |||||||||||
Pre-heating time | +60ºC~+200ºC ,Within 25 min | |||||||||||
Recovery time | High-Temp Exposure 30 min | |||||||||||
Low-Temp Exposure 30 min | ||||||||||||
Recovery time within 3 min | ||||||||||||
Safety device |
No fuse breaker, over pressure, over heat and over current protection for compressor,over temperature protection, over load protection for blower, dry heat protection |
|||||||||||
Standard accessory | Cable port(portΦ50mm)*1, shelves*2 | |||||||||||
Interior material | Stainless steel plate(SUS 304) | |||||||||||
Exterior material | Baked painting steel or stainless steel(SUS304) | |||||||||||
Insulation material | Rigid polyurethane Foam+glass fiber wool | |||||||||||
Refrigeration system | Water Cooled | |||||||||||
Semi-hermetic compressor, cascade refrigeration system, CFC free refrigerant(HFC-507 and HFC-23) |
||||||||||||
Controller | Panel:7-inch LCD Touch panel, Chinese or English display selectable | |||||||||||
Operation model:Program or fix point running | ||||||||||||
Memory capacity:120programs,1200steps, all repeat 999cycles,part repeat 99 cycles. | ||||||||||||
Accuracy:Temp.:0.1% of F.S±1 digit Humidity:0.1% of F.S±1 digit | ||||||||||||
Input:Temp.:pt-100 Humidity:pt-100 or ~5V DCV | ||||||||||||
Ambient Temp. | +5ºC~+35ºC | |||||||||||
Power | AC 380±10% 50Hz ,3 phase 4 wires +Ground Wires | |||||||||||
Note:1. We reserve the right to change specifications without prior notice 2. Customized sizes and configurations available |
2. Application
The rubber thermal shock climatic chamber, indispensable in materials industry such as metal, plastic, rubber, electronics etc, is applicable to test temperature endurance of material structure and composite materials under a rapid shift from extremely high temperature to a extremely low temperature or reverse, so as to find in shortest time the chemical changes or physical damages caused by thermal expansion and contraction.
3. Below are differences between 3-zone and 2-zone thermal shock chamber:
3-zone thermal shock chamber:
three chamber in total: test space, high temp. chamber and low temp. chamber;
Advantage: slight limitation for test sample’s weight, the test sample keep still, this can reduce the impact to samples by moving it, can be used for on-load testing.
Compared with 2-zone type, relatively low failure rate, low cost.
2-zone thermal shock chamber:
Only two chambers: high temp. Chamber and low temp. chamber
Advantage: short conversion time, smaller space needed
Disadvantage: test sample moving. test samples’ size is limited by the basket size
4.Introduction of thermal shock chamber:
1.2 Corresponding standard:
1 GB/T2423.1-1989 low-temperature testing method
2 GB/T2423.2-1989 high-temperature testing method
3 GB/T2423.22-1989 change temperature test
4 GJB150.5-86 temperature impact test
5 GJB360.7-87 temperature impact test
6 GJB367.2-87 405 temperature impact test
5. About thermal shock test chamber:
Contact Person: Anna Hu
Tel: +8618098282716